Browse all practice questions for the VT-10 Primary INAV Ground School Instrument 3 Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

VT-10 Primary INAV Ground School Instrument 3 Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Ground Speed calculation requires you to be outside of what range?
  • What is the standard final approach airspeed used during circling maneuvers?
  • Which statement best describes the effect of unexpected weather, NAVAID outages, or aircraft malfunctions on flight clearance?
  • Between successive points on the ROUTE OF FLIGHT on the 1801, what is placed?
  • What is the equation used when leading a turn from an arc?
  • For Ground Speed calculation, IAS must be set for TAS.
  • FLIP planning documents are updated by what three things?
  • What formula is used to calculate VDP?
  • In enroute delay notation ABY/D00+20, what does DHH+MM indicate?
  • If destination weather is 3000-3 or better, is alternate filing required?
  • When flying no-gyro vectors, you must acknowledge the controller directives until when?
  • How can you recognize a HILO procedure turn approach?
  • In a Procedure Turn, you will overfly the IAF if the aircraft heading is greater than how many degrees from the outbound course?
  • In Point to Point navigation, you must TIM the station and set CDI to the desired ________.
  • A flag with an "R" in it is what?
  • What provides 1000' of terrain/obstacle clearance and 2000' in mountainous terrain AND can be less than the MEA/MOCA?
  • MOCA's specify NAVAID reception distance between NAVAIDs as what value?
  • In the 1801 annotation GEO/N0270/A045, what does A045 denote?
  • In a radar pattern, aside from assigned headings and altitudes, what other item must be read back?
  • From March to November, what is the UTC time offset for Pensacola, and how do we translate that to UTC/Zulu Time?
  • (L) and (T) symbols on a high altitude enroute chart refer to a NAVAID having a ___________ on its usable range.
  • Which publication contains the GPS navigation terms and definitions used in flight operations?
  • When should ATIS be copied for the Destination airport?
  • MOCA's provide obstacle clearance and acceptable navigation signal coverage within ___ NM of the NAVAID.
  • Which resource would you use to verify field contract fuel availability?
  • To calculate Ground Speed, which four conditions must be met?
  • When requesting radar departure, ATC will provide routing to the first point on your flight plan in the form of what?
  • When performing an approach, what two criteria must be met in order to land?
  • Which type of departures provide heading and altitudes to fly until capable of maintaining your cleared flight route using on-board navigation systems?
  • If you are using a feeder route to the IAF and cleared for the approach, you are considered ______ on the approach and you can ______ to the altitude depicted on the feeder route.
  • Circling Airspeed for CAT A is
  • To determine the type of fuel available at an airfield, you should reference which document?
  • In CNAF fuel planning, the fuel amount is expressed in which unit?
  • Timing for a Procedure Turn begins when?
  • What is the default holding pattern turn direction when not specified?
  • Which symbol identifies the maneuvering side of a procedure turn?
  • EET on the 1801 should be listed as which format?
  • Which type of call includes the distance remaining at each 1000-foot marker (board) and is made until 40 knots airspeed is acquired?
  • When should you slow down to 120-150 KIAS on approach?
  • The DRAFT report includes which elements?
  • Which of the following is NOT a criterion for calculating Ground Speed?
  • On an ASR approach, the location of the Missed Approach Point (MAP) is defined by which entity?
  • Which book contains amendments to SIDs and Terminal High/Low Altitude volumes?
  • If no transmissions are received on ASR FINAL while vectored, you should wait for how many seconds before attempting contact?
  • If told to not acknowledge further transmissions on a GCA approach, what is the exception?
  • If there is no FAF on a low altitude procedure turn approach, where should you consider the FAF?
  • For Point to Points, if proceeding to a fix with a smaller DME, roll your heading closer to the _______ Pointer Head.
  • Along with the DP, NAVAIDS, and Fixes; you should add named or unnamed fixes or points with greater than how many degrees of course change to define the route in your Jet Log?
  • Where in ForeFlight would you access Radar Minimums for radar approaches?
  • Which of the following correctly completes the flight planning values for Start/Taxi/Takeoff, climb to 12,000', and per-approach fuel?
  • What is required to be read back to the controller when operating in a radar pattern?
  • In the Airport ID notation 280 (L) 72, what does the 72 represent?
  • If a DRAFT report is required, which briefing should occur first?
  • On charts, which route type is identified by the letter V?
  • T/F: Not all airfields depicted in Green on a Low Altitude Enroute Chart have an approved IAP and/or RADMIN in the DOD FLIPS?
  • For preflight planning at an alternate, you must add to the published minimums for precision approaches which value?
  • While being vectored on Radar Vectors, you should contact ATC if no transmissions are received for how long?
  • An airport depicted on an Enroute Chart with Brown color has which minima status?
  • Which statement about the T-6A aircraft is true?
  • When moving to a new controller, what is the correct sequence of actions with the frequency?
  • If destination weather meets published minimums but not 3000-3, alternate weather for non-precision must be ____________ and precision must be _______
  • What is the lowest altitude which Navigational fix can be crossed while climbing to meet the MEA on the next airway?
  • Solid Black Triangle on a Low En Route Chart depicts what?
  • In Case 3 scenario for Flight Planning for Alternates, what is true?
  • When do you use the 1801-C?
  • Start the descent when the pilot chooses, using any rate of descent and leveling off at an intermediate altitude. This describes which type of descent?
  • From November to March, what is the UTC offset for Pensacola, and how do you convert local time to UTC?
  • You can legally file to a destination having forecast weather of ______ +/- 1 hour of your ETA?
  • If you have major changes to your flight plan enroute, what can you expect from ATC?
  • When should you provide a Missed Approach Review and MAP/Climbout instructions?
  • OROCA's provide _____ Obstacle and _____ Mountain Clearance with no Guarantee of NAVAID reception
  • For GCAs, when should the approach brief normally be initiated?
  • If you must descend at the IAF on a procedure track, when should you begin your descent?
  • Which element is the first in the FETL mnemonic?
  • Information on Special Use Airspace such as MOAs is found in which document?
  • Where do you find published DPs?
  • When preparing an approach request, what combination best describes required content?
  • In a holding pattern, establishment occurs at the moment you pass which point for the first time?
  • Jet route altitudes start at what altitude and go up to what flight level?
  • Which resource would you use to verify into-plane fuel contract information for a field?
  • Information regarding arresting gear is located in which publication?
  • For the Departure/Destination/Alternate Aerodrome block on an 1801, insert _____ if the LOCID contains a number, no LOCID assigned, or not known
  • Which FLIP document contains specific information on maximum holding speeds, holding patterns, and how controllers will issue holding instructions?
  • When should the Holding Brief be given?
  • For cruising altitudes, which parity is used when flying Southwest?
  • The profile view symbol 'v' denotes Visual Descent Point.
  • As you approach the IAF with a heading within 90 degrees of the initial course, you do not have to overfly the IAF and may use normal lead points to intercept the published course. This statement is true.
  • If you are flying a DP, the controller gives you a new heading that takes you off the Departure Procedure transition without any additional info; is the DP considered cancelled?
  • When do you raise the landing gear on takeoff?
  • What type of taxi is requested from Ground at unfamiliar airfields?
  • If an airfield has numbers or does not have 4 characters, how are the put into the ROUTE OF FLIGHT block on an 1801?
  • Minimum Enroute Altitude (MEA) on a chart is depicted by which of the following?
  • Altitudes published on a terminal/feeder routes provide the same obstacle protection as an ______.
  • If you are given a different altitude by ATC than that depicted by the DP, should you consider the DP canceled?
  • Which flag indicates Minimum Reception Altitude (MRA)?
  • In the last 1000 feet of runway remaining, runway centerlights are which color?
  • When should you initiate the first Time Hack?
  • Which source would you consult to determine the fuel type information for an airfield?
  • Which altitude thresholds are included in the outside FAF warning list aside from FL180?
  • Which statement best describes BINGO measurement?
  • In order to calculate Ground Speed, you must be on what navigational feature?
  • If no weather forecast is available for a specific airport, can you plan or file for that location?
  • On an airway, where does the NAVAID changeover point occur?
  • Which of the following scenarios can lead to a change in your in-flight clearance, either at your request or by ATC?
  • MCA stands for which term?
  • Reserve fuel endurance is specified at what altitude?
  • During a circling maneuver, what airspeed is flown on final and what is the radius of clearance?
  • What area is always shown to scale on an Instrument Approach Plate?
  • What is the minimum airspeed to use when circling to land on an instrument approach?
  • What does the restriction "RADAR REQUIRED" imply when planning an alternate?
  • The Terminal Change Notice (TCN) is used to amend which items?
  • Minimum Enroute Altitudes (MEA) provide ______ of Obstacle Clearance and _____ of Mountain Clearance and guarantees NAVAID reception between _____ NAVAIDS
  • The DA/DH for a PAR approach is determined by which combination?
  • For any ETA changes, when must you notify ATC?
  • For preflight planning at an alternate, you must add to the published minimums for nonprecision approaches which value?
  • Which altitude provides 1000 feet of terrain clearance within 25 nautical miles?
  • What is the takeoff minimum expression for non-precision and precision operations under Standard Instrument Rating?
  • Pilots shall not file through areas for which a WW has been issued unless storm development has not progressed as forecasted and verified by DOD forecaster/FSS. What condition allows filing anyway?
  • What does 'NoPT' mean?
  • During a 45/180 Procedure turn maneuver, how long should you time the 45-degree leg before turning 180 degrees to intercept inbound course?
  • What is identified by a 'v' on the Profile View?
  • Glide slope helps maintain the proper approach angle, which is normally between which two values in degrees?
  • When transitioning from one Victor airway to another, should you lead your turn?
  • Where can you find Instrument Penetration Approaches?
  • When flying an ASR approach, the MAP is defined by what?
  • Ground Speed calculation requires flight in what regime?
  • When handed to a new controller, what shall you do?
  • Regarding Lost Communications, what is the priority for heading to be maintained?
  • For a procedure turn, the initial outbound leg distance is marked by which DME?
  • Circling Airspeed for CAT B is
  • Minimum Obstruction Clearance Altitude (MOCA) is depicted on a chart by which feature?
  • Which item is not among the three that update FLIP planning documents?
  • The FLIP GP document provides information about what?
  • How are enroute delays annotated on the Route of Flight on an 1801?
  • In triple drift correction, you triple the inbound course correction and switch to the opposite left or right when going on the outbound course. What are the two course segments involved?
  • To do a Practice Approach at a Drop-In Airfield, what type of flight plan should you file?
  • In IMC, vectored for a GCA approach, and you lose all communications before receiving lost comms instructions, how should you fly?
  • When are you required to report airspeed changes to Center?
  • If you plan to fly an alternate airfield approach/practice approach and wish to prepare your DRAFT report before the IAF, you should subtract how many pounds from the current fuel to estimate your fuel at the divert initiation?
  • If you fly 8 DME in one minute, what is your approximate ground speed in knots?
  • A white 'T' in a black upside-down triangle indicates that takeoff minimums are not standard and/or departure procedures are published.
  • Which of the following is not a type of Approach Brief?
  • If no holding is required, the approach brief should be given when?
  • In a Localizer Back Course approach, the CDI must be set to the reciprocal of the APP CRS course. Which box on the approach chart provides this course?
  • If no transmissions are received on PAR FINAL while vectored, you should wait for how many seconds before attempting contact?
  • Lead all turns greater than 30 degrees except for what three events?
  • What information is given for the Holding Brief, and what mnemonic is used?
  • When planning for an alternate airfield, what symbol and restrictions would be a dead give away on the approach plate Briefing section that you cannot use it as an alternate airfield?
  • Which item is NOT listed among required IFR equipment prior to takeoff in controlled airspace?
  • White Triangle on a Low En Route Chart depicts what?
  • For Localizer Back Course approaches, what must you set in the CDI?
  • Maximum Authorized Altitude (MAA) is depicted on charts in which format?
  • What does the DRAFT report stand for?
  • Which term describes a restriction on the usable range of a NAVAID as indicated by L and T symbols?
  • Date on the DD-1801 is based on which time?
  • For the DRAFT adjustment, subtract 50 pounds from current fuel to estimate fuel at divert initiation. Which of the following is true?
  • Traffic Advisories are a (Mandatory / Non Mandatory) service provided by controllers to aircraft operating in the radar pattern.
  • Where can you find the formatted guide for changing flight plans in-flight?
  • What does an airport depicted in Brown on an Enroute Chart indicate?
  • Altitude warnings for descents inside the FAF are given when?
  • From the threshold to 3000 feet remaining, runway centerlights are which color?
  • For planning a mission in the United States, which reference provides supplementary airfield information?
  • In Case 2 scenario for Flight Planning for Alternates, what is the alternate requirement when destination ETA +/- 1 hr is published mins (at least 200-½) up to but not including 3000-3?
  • In the 1801 notation GEO/N0270/A045, what does GEO represent?
  • What is the best practice to ensure TAS is used in the Ground Speed calculation?
  • What is the holding airspeed?
  • For Point to Points, if proceeding to a fix with a larger DME, roll your heading closer to the _________ Needle Head.
  • What is the one exception to the Approach Criteria requirement?
  • On a PAR/ASR, you are being guided by which and not a which?
  • If ATC issues a new heading off a DP transition with no extra information, the DP is considered canceled.
  • For ILS approaches, the point where you execute a missed approach is the ___________.
  • If you change destination, switch from VFR to IFR, or change routing en route, what must you do?
  • For IFR flights in controlled airspace, which equipment must be operable prior to takeoff?
  • If DME is not available for the outbound leg of a 45/180 PT, what timing should you use?
  • In IMC, when circling is not authorized, the minimums are expressed as 1000-3. What does the 3 represent?
  • What are the airspeed and configuration for Final Approach Course?
  • Which case number describes a scenario where an alternate must be filed despite not needing it, yet it remains on the flight log?
  • What does the acronym FETL stand for in the Holding Brief?
  • Initial OPS Check _____ be performed immediately after checking in with Departure, safety of flight permitting. Subsequent OPS checks are __________ to be initiated after each wings level call.
  • In Case 2, what must the alternate minima include?
  • Before you initiate a descent on the inbound leg of a HILO approach, you must be established on the _________ course
  • Which statement about using the 1801 form for flights is true?
  • If the holding fix is a VOR, you are abeam the fix when the aircraft passes a radial ____ off the holding course radial.
  • What are the three types of orbits in a holding pattern?
  • After liftoff during an ITO, you should be committed to attitude instrument flying procedures due to potential for what?
  • Which sequence best describes the order of briefing items if a holding is planned?
  • From 3000 feet remaining to 1000 feet remaining, runway centerlights are which pattern?
  • If runway is not in sight at the VDP or MDA, do you execute a missed approach?
  • Which holding entry technique involves a teardrop path?
  • Advise the pilot for deviations more than ____ ft off assigned altitudes, _____ KIAS off assigned airspeed, or ____ degrees off assigned heading.
  • What information do you need to calculate your ground speed?
  • During holding over a VOR, abeam is achieved when the aircraft crosses the radial offset of which value from the holding course?
  • What does an airport depicted in Green on an Enroute Chart indicate?
  • Holding timing is 1 minute below 14,000 feet and 1.5 minutes above 14,000 feet.
  • Do all localizer antennas provide DME?
  • Regarding Lost Communications, what is the altitude that should be maintained?
  • Minimum Safe Altitudes provide 1000 feet of clearance within 25 NM. Which of the following best describes this statement?
  • On a low altitude enroute chart, an airfield depicted with a brown symbol indicates what?
  • Circling Airspeed for CAT C is
  • Which instruction best describes how to handle a loss of comms when vectored for a GCA approach?
  • Which factor is NOT included in determining the minima for commencing an approach?
  • Circling Airspeed for CAT E is
  • The Z symbol with numbers on top and bottom on a chart depicts which of the following?
  • What is the minimum final approach speed?
  • Where do you find airport/field info?
  • A brown symbol on a low altitude enroute chart indicates that the airfield does not have what?
  • True or False: Changing your TAS by +/- 5% or 10 Knots is a required report to ATC.
  • BINGO is measured from which to which?
  • Time should be rounded to the nearest what, fuel rounded to the nearest what, and distance rounded to the nearest what?
  • How can you determine if a field has contract fuel for military aircraft?
  • In Point to Point navigation, if proceeding to a fix and the DME increases, roll your heading closer to which needles head?
  • In the Alternate profile I plan, what are the two endpoints called?
  • GPS provides highly accurate position and velocity information, and precise time, on a global basis. How is the GPS system affected by weather?
  • Which chart symbol denotes non-compulsory position reports?
  • If you have at least ZERO pounds of Spare fuel, can you legally fly your route under conditions expected in preflight planning?
  • The 1801-C is designed to accommodate how many additional legs/stopovers?
  • What is the lowest altitude at which an intersection can be determined by a NAVAID?
  • Which altitude is designated as the uncontrolled ejection altitude for warnings outside the FAF?
  • When filing for a drop-in approach at an airport that has numbers as their ICAO, how is it entered on the ROUTE OF FLIGHT?
  • Where can you locate the formatted guide for changing flight plans in-flight?
  • Timing at the FAF begins when?
  • What is the primary purpose of a Jet Log?
  • Which type of Approach Brief is used for ILS, PAR, ASR, VOR, or LOC approaches?
  • Which statement is correct regarding alternate planning adjustments to minima?
  • If you are not provided with specific turns on a holding pattern, what type of turns should you execute?
  • What is another name for UTC used in aviation timekeeping?
  • To determine if an airfield has an into-plane fuel contract, reference which resource or contact?
  • Circling Airspeed for CAT D is
  • To execute a missed approach while circling to land from a VOR, start climbing towards the ________.
  • MOCA's provide ___ NM of NAVAID reception between NAVAIDs while having ______' Obstacle and ______' Mountain Clearance
  • PIREP Information/Format, Runway Condition Reading, Braking Action, and Approach Lighting configurations can all be found in which Publication?
  • What is the minimum fuel required to be onboard upon arrival at Destination IAF, to comply with CNAF fuel requirements to be able to fly to/land at an alternate?
  • On a NoPT approach, which maneuver is not permitted?
  • Jet Routes on a navigation chart are identified by which letter?
  • When using a feeder route to the IAF, to what altitude are you permitted to descend?
  • For VOR approaches, you will use either _____ or _______ to determine arrival at the FAF.
  • For a Northeast-bound route, the cruising altitude should be which parity?
  • Before enroute descent for an approach, what information should you check in with ATC?
  • For ILS approaches, when shall you set BAC and complete Before Landing Checklist?
  • If you are flying a low altitude procedure turn approach, can you begin the course reversal at any point?
  • The 20-minute CNAF fuel requirement is based on maximum endurance airspeed at an altitude of what?
  • Can a single-piloted aircraft use PAR, ASR, RADAR-Required Approaches for Alternate Airfield Planning?
  • In Case 1 scenario for Flight Planning for Alternates, what is the required alternate minimum when destination ETA +/- 1 hr is 0-0 up to but not including published mins (not less than 200-½)?
  • The EET entry on the DD 1801 for an IFR flight is the total of which time?
  • What is the spare fuel requirement for the T-6A to legally fly?
  • Which of the following best describes the intercept lead-point technique near the initial approach course when within 90 degrees of the initial course?
  • What provides 1000 feet of terrain/obstacle clearance within 25 NM?
  • Height Above Airport (HAA) is associated with which type of instrument approaches?
  • On High Altitude enroute charts, airports have at least one hard surfaced runway with a minimum runway length of how many feet?
  • When should the DRAFT report to the IP be offered?
  • Which statement best describes who can sign a filed flight plan?
  • Holding timing begins when you are outbound and abeam the holding fix, or wings level if unable to determine abeam.
  • The takeoff time on the DD-1801 is based on what time?
  • Which two instruments are used to confirm two positive rates of climb for gear retraction?
  • In the 1801 annotation GEO/N0270/A045, what does N0270 denote?
  • What is the minimum speed on final?
  • Which form is used to file the initial leg of a STOPOVER flight?
  • Alternate "Profile I" plan is to fly from _____ to ____ at ______ feet
  • The following statement is true or false: The T-6A is considered a 'single-piloted' aircraft regardless of crew.
  • TW-6 SOP states that T/O in conditions less than standard minimums _______ authorized unless approved by TW-6
  • In a PAR approach, how is the DA/DH determined?
  • Where would you find information regarding arresting gear used in flight operations?
  • For T/O minimums with Standard Instrument Rating, Non-Precision T/O minimums must be ___-__ and for Precision must be ___-__ or _____' RVR
  • At what point during the en route phase should the Field Brief be given?
  • Which type of Approach Brief is used for Radar Vectors?
  • Minimum Safe Altitudes provide how many feet of terrain/obstacle clearance within how many nautical miles?
  • Who is authorized to sign a flight plan?
  • Are radar vectors provided by a Published DP?
  • MCF stands for what in CNAF fuel planning?
  • The NAVAID changeover point is depicted by which symbol?
  • Which drift correction technique is used when flying holds?
  • To locate altimeter changeover procedures, what is the best starting point?
  • Low altitude approach procedures ensure ________ clearance and ____________ from other IFR aircraft.
  • Where can you find the official definitions of GPS navigation terms?
  • Should you still place an entry for an alternate on your flight log when the case indicates no alternate is required?
  • Which flight level is listed as a warning threshold for descents outside the FAF?
  • VOR approaches are usually associated with which teardrop type?
  • If you are doing a Practice Approach, what information do you count on your flight log?
  • What are the three entry procedures into a holding pattern?
  • In the notation 280 (L) 72, what does the letter L signify?
  • Which type of Approach Brief is used for GCA approaches?
  • GPS Routes on a chart are identified by which color?
  • The publication that provides standardized departure procedures (DPs) is found in which source?
  • The DD Form 1801 is used for all flights within the US and for flights from the US to Canada.
  • What is the minimum runway length for normal T-6 Ops?
  • If you lose comms while taxiing to the runway and see flashing white light signals, what should you do?
  • What on the Approach plate is used to aid pilots during landing transition by helping to identify the runway environment?
  • Where can you find the Airport Diagram information?
  • For 45/180 Procedure turns, how long should the outbound leg be flown?
  • The minimum runway length for normal T-6 Ops applies to which surface condition?
  • Reserve fuel endurance is 20 minutes.
  • Arrange the departure planning events in the proper order: 1) Obtain ATIS, 2) Field Brief, 3) Time Hack, 4) Contact Tower.
  • If destination weather is 0-0 up to but not including published minimums, what alternate airfield weather is required for preflight filing?
  • Where do you find Radar Approach Minimums?
  • What are the airspeeds from IAF to FAF?
  • The EET entry on the DD 1801 stands for Estimated Enroute Time. Which statement best describes EET's purpose?
  • At what point is a missed approach authorized if the runway is not in sight?
  • Altitude warnings for descents outside the FAF are given when?
  • A flag with an "X" in it is what?
  • What time is used for your TOTAL EET on your 1801?
  • Solid black triangle indicating compulsory position reports appears on which chart type?
  • What does 0-0 indicate in weather minimums?
  • How are GPS MEA's depicted on the chart?
  • How many pounds of fuel represent CNAF's 20 minute flight at maximum endurance airspeed at 10,000 feet?
  • The localizer signal is useable and accurate out to a range of ___ NM from the antenna
  • If holding is required, the approach brief can be given when?
  • Victor Routes on a chart are identified by which letter?
  • Which statement is true about the relationship between localizers and DME?
  • Which departure type uses radar vectors to begin navigation until you can maintain the cleared route using on-board navigation systems?
  • When flying GPS approaches, which minimums may be used?
  • If a controller issues a clearance to climb and maintain to an altitude different from the DP, you should continue the DP route and _________ all of the remaining DP altitude restrictions.
  • Regarding Approach Criteria, when commencing, approach minima shall be no less than which combination?
  • If circling is not authorized with a two plane formation departure into IMC, ceiling and vis must be at least ____?
  • Which statement best describes the four Ground Speed criteria?
  • What symbol indicates GPS-derived MEA on en-route charts?
  • If your heading is within 90 degrees of the outbound penetration course on a radial/straight-in approach, you are not required to overfly the IAF and may use normal lead points to intercept the course. Within how many degrees is this true?
  • What is the standard action when on the ground with flashing white light signals?
  • If the outbound leg on a hold is longer than 1 minute, what drift correction should you use after flying 1 minute?
  • The takeoff time on the DD-1801 is based on what time standard?
  • When approaching the IAF, if your heading is within 90 degrees of the initial course, you may use normal lead points to intercept the published course.
  • When requesting radar departure, you will receive which of the following to the first point listed on your flight plan?
  • According to the FAR/AIM, you should report the ______ and _________ upon reaching a holding fix to ATC.
  • If you have less than zero pounds of spare fuel, your flight plan is considered illegal and must be changed.
  • NAVAIDs that do not have a radio class symbol are assumed to be which category?
  • There is no T/O ceiling or visibility restrictions for Pilots who have a _________ instrument rating
  • After you provide AIR to Approach, you should include what into your request?
  • During pre-flight planning, weather minimums at the ETA should be accounted for which of the following?
  • Which feature identifies OROCA on a navigation chart?
  • When do you configure to BAC on a GCA approach?
  • When flying in a radar pattern downwind, maintain _____ to ____ KIAS in what type of configuration?
  • Which statement about jet route altitude ranges is true?
  • Which document contains information on Special Use Airspace such as MOAs for flight planning?
  • When reading clearance back to ATC, you should read back what information?
  • When requesting radar departure on the 1801, where is the instruction placed and how should it read?
  • MOCA stands for which of the following?
  • What is the clearance distance specified for circling maneuvers?
  • When should you perform the Descent Checklist?
  • According to CNAF 3710, reserve fuel shall be a percentage of planned fuel requirements.
  • If you experience lost communications in VMC conditions, are you required to land at the nearest suitable airport?
  • Glide slope angle is typically between 2.5 and 3 degrees.
  • When are you considered established in the holding pattern?
  • Which flag indicates Minimum Crossing Altitude or Minimum Turning Altitude?
  • Altitude Warnings for Climbs are given when?
  • OROCA's provide only ___________ clearance.
  • During an instrument approach, if ATC instructs you to contact Tower at the FAF, what should you report?
  • What is the final decision point for determining if you have the required weather for takeoff on an IFR flight plan?
  • If the local Pensacola time is 3:00 PM in November through March, what is the corresponding UTC time?
  • When determining EFR at IAF for the practice drop in approach, what should you do with the total EFR number?
  • Which statement correctly describes the Maximum Authorized Altitude notation on charts?
  • What is the typical ATC response when there are major changes to your enroute flight plan?
  • What altitude is specified for the Alternate Profile I plan?
  • In the 1801 annotation for changes to airspeed or altitude during the route of flight, what does the middle segment indicate?
  • Which feature on an Instrument Approach Plate is used to identify the runway environment during the landing transition?
  • Takeoff Time on the 1801 is based on what time?
  • What range should you maintain on the downwind leg in a radar pattern?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy